Ocean International

Introduction of Blown Film Machine :-

Blown Film Machine is a technology that is the most common method to make plastic films, especially for the packaging industry. The process involves extruding a tube of molten polumer through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene is used with this process, and other materials can be used as blends with these polymers. A diagram of a blowing film process.

The Film Blown Film Machine

Typically, Blown Film Machine is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common.

This procedure consists of four main steps:

The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous liquid . This molten plastic is then forced, or extruded , through an annular die.

Air is injected through a hole in the center of the die , and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film.

The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter.

After solidification t the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated.

Advantages of Blown Film Machine:-

Blown Film Machine generally has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.

Blown Film Machine can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220°C., where as the temperature of blown film is about 135°C. Furthermore, the cost of the equipment is approximately 50% of a line.

Applications of Blown Film Machine:-

Consumer food wrap from plastic wrap article.

Agricultural film

Bags

Industry packaging, shrink film , stretch film

Consumer packaging, food wrap, transport packaging ( Figure )

Laminating film

Barrier film

Multilayer film

Research has been done to explore the incorporation of blown film extrusion into the large-scale manufacturing of carbon nanotube and nanowire films.
Blown Film Machine

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 WORKING DAYS

Introduction of Blown Film Machine :-

Blown Film Machine Exporter is a technology that is the most common method to make plastic films, especially for the packaging industry. The process involves extruding a tube of molten polumer through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene is used with this process, and other materials can be used as blends with these polymers. A diagram of a blowing film process.

The Film Blown Film Machine

Typically, Blown Film Machine Exporter is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common.

This procedure consists of four main steps:

The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous liquid . This molten plastic is then forced, or extruded , through an annular die.

Air is injected through a hole in the center of the die , and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film.

The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter.

After solidification t the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated.

Advantages of Blown Film Machine:-

Blown Film Machine generally has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.

Blown Film Machine can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220°C., where as the temperature of blown film is about 135°C. Furthermore, the cost of the equipment is approximately 50% of a line.

Applications of Blown Film Machine :-

Consumer food wrap from plastic wrap article.

Agricultural film

Bags

Industry packaging, shrink film , stretch film

Consumer packaging, food wrap, transport packaging ( Figure )

Laminating film

Barrier film

Multilayer film

Research has been done to explore the incorporation of blown film extrusion into the large-scale manufacturing of carbon nanotube and nanowire films.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Pay Mode Terms: L/C (Letter of Credit),T/T (Bank Transfer),Other
• Port of Dispatch: Mundra, Gujarat
• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Days

Blown Film Plant

Blown Film Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Plant:-

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Line

Blown Film Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Line:-

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Working Days

Introduction of Blown Film Machine Unit:-

Blown Film Machine Unit is a technology that is the most common method to make plastic  films, especially for the packaging industry. The process involves extruding a tube of molten polumer  through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene  is used with this process, and other materials can be used as blends with these polymers. A diagram of a blowing film process.

The Film Blown Film Machine Unit

Typically, Blown Film Machine Unit is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common.

This procedure consists of four main steps:

The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous   liquid . This molten plastic is then forced, or extruded , through an annular die.

Air is injected through a hole in the center of the die , and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film.

The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter.

After solidification t the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated.

Advantages of Blown Film Machine Unit:-

Blown Film Machine Unit has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.

Blown Film Machine Unit can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220°C., where as the temperature of blown film is about 135°C. Furthermore, the cost of the equipment is approximately 50% of a line.

Applications of Blown Film Machine Unit:-

Consumer food wrap from plastic wrap  article.

Agricultural  film

Bags

Industry packaging, shrink film , stretch film

Consumer packaging, food wrap, transport packaging ( Figure  )

Laminating  film

Barrier film

Blown Film Machine Unit

Research has been done to explore the incorporation of blown film extrusion into the large-scale manufacturing of carbon nanotube and  nanowire films.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Working Days

Co - Extrusion Blown Film Plant:-

Co - Extrusion Blown Film Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Co - Extrusion Blown Film Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Co - Extrusion Blown Film Plant is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Co - Extrusion Blown Film Plant:-

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Machine

Blown Film Machine in India with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machine in India has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Applications of Blown Film Machine:

· Film for Shopping Bags

· Film for Liners

· Stretch Film

· Shrink Film

· Lamination Film

· Biodegradable Film

Blown Film Machine with the best combination of technology and performance.

These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment. Blown Film Machine has a great demand in global market for its wide range of packaging products that can be produced from it.

Blown Film Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc.

It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be
produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 Days

Blown Film Extrusion Line

Blown Film Extrusion Line are used for varied crucial application in flexible packaging, which demand vital film properties like dart impact strength, puncture resistance, hot tack strength, gloss, oxygen and moisture barrier etc.

Blown Film Extrusion Line is comparatively strong than two layer and mono layer blown films. It has strong impact in packaging industry as this product bears multiple protection properties including puncture and heat resistant, less or zero attraction to moisture and oxygen, etc. Multilayer Blown Film Plant is suitable for producing high barrier wrapping and stuffing material for packing food products, processed fluid consistency food items, etc. Multilayer blown film line can also be produced with this machine.

Ocean extrusions is a leading plastic extrusion machinery manufacturer & exporter in India, having core expertise in comprehensive range of extrusion machinery for plastic including plastic extruder such as multi layer blown film plant, mono layer blown film plant, air bubble sheet plant, raffia tape stretching plant, extrusion coating lamination plant, co-extrusion two layer blown film plant, PP-TQ blown film plant, monofilament plant, sutli plant, PP box strapping line, HDPE box strapping line, PET box strapping line and plastic reprocessing plant. Ocean extrusions Pvt Ltd is a well known trusted name for providing customized solutions of plastic extrusion machineries.

Blown Film Extrusion Line : Multi layer co-extrusion blown film lines are available in a wide range of configurations from two to nine layers to produce variety of films like lamination grade films, liquid packaging films, ultra high barrier films, high dart FFS resin sacks films, meat and cereal packaging films, oil packaging films, pharma and medical grade films, pallet hooding shrink/stretch films, green house films, silage and mulch films, geo membrane and chemical / soap packaging films 3 Layer Co-extrusion Plastic Blown Film machine Polypropylene Blown Film Plant blown film plant, blown film plant, blown film extruder, blown film extrusion machine and monolayer blown film extrusion line for plastic film, tubing and bags. Film for Shopping Bags, Shrink Film, Biodegradable Film, Lamination Film two layer blown film line including multi layer blown film plant, raffia tape lines, air bubble sheet plant, PP HDPE box strapping plant ABA Multi layer Blown Film Machine Layer Film Line blown film plant, blown film extruder, blown film extrusion machine and monolayer blown film extrusion line for plastic film, tubing and bags blown film plant multilayer film line pp blown film machine multilayer extrusion film line PE Blown film machine Plastic processing machinery Multilayer co-extrusion blown film machine PE Blown film machine, Plastic processing machinery, Multilayer co-extrusion blown film machine, HDPE /LDPE blown film machine and LDPE/LLDPE/HDPE Blown Film line plastic film extruder PP blown film line, LDPE blown film machine, Plastic Film Extruder, Lab Film Extruders, Rotating Die, blown film plant, PP blown film line, LDPE blown film machine, HDPE blown film plant, LLDPE film Two Layer Blown Film Plant India, Two Layer Plastic Garbage Bags plants Manufacturers, two layer blown film line with wide width and the features of two layer blown film line is low investment, power efficient and high - speed plants and it is used for various industries such as Film for Shopping Bags, Shrink Film, Biodegradable Film, Lamination Film two layer blown film line Wide Width LLDPE Blown Film Plant carry bag making machine blown film plant Multilayer Blown Film.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 150 - 300 ( kg/hr )
• Delivery Time: 90 Working Days

Co Extrusion Blown Film Machine

Co Extrusion Blown Film Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Co Extrusion Blown Film Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Co Extrusion Blown Film Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Applications of Co Extrusion Blown Film Machine:

·         Film for Shopping Bags

·         Film for Liners

·         Stretch Film

·         Shrink Film

·         Lamination Film

·         Biodegradable Film

Co Extrusion Blown Film Machine with the best combination of technology and performance. 

These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment. Co Extrusion Blown Film Machine has a great demand in global market for its wide range of packaging products that can be produced from it.

Co Extrusion Blown Film Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc.

It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be
produced from this single plant.Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 WORKING DAYS

Blown Film Machine Manufacturer

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 DAYS

Introduction of Blown Film Making Machine:-

Blown Film Making Machine is a technology that is the most common method to make plastic  films, especially for the packaging industry. The process involves extruding a tube of molten polumer  through a die and inflating to several times its initial diameter to form a thin film bubble. This bubble is then collapsed and used as a lay-flat film or can be made into bags. Usually polyethylene  is used with this process, and other materials can be used as blends with these polymers. A diagram of a blowing film process.

The Film Blown Film Making Machine

Typically, blown film extrusion is carried out vertically upwards, however horizontal and downward extrusion processes are now becoming more common.

This procedure consists of four main steps:

The polymer material starts in a pellet form, which are successively compacted and melted to form a continuous, viscous   liquid . This molten plastic is then forced, or extruded , through an annular die.

Air is injected through a hole in the center of the die , and the pressure causes the extruded melt to expand into a bubble. The air entering the bubble replaces air leaving it, so that even and constant pressure is maintained to ensure uniform thickness of the film.

The bubble is pulled continually upwards from the die and a cooling ring blows air onto the film. The film can also be cooled from the inside using internal bubble cooling. This reduces the temperature inside the bubble, while maintaining the bubble diameter.

After solidification t the frost line, the film moves into a set of nip rollers which collapse the bubble and flatten it into two flat film layers. The puller rolls pull the film onto windup rollers. The film passes through idler rolls during this process to ensure that there is uniform tension in the film. Between the nip rollers and the windup rollers, the film may pass through a treatment centre, depending on the application. During this stage, the film may be slit to form one or two films, or surface treated.

Advantages of Blown Film Making Machine:-
Blown film generally has a better balance of mechanical properties than cast or extruded films because it is drawn in both the transverse and machine directions. Mechanical properties of the thin film include tensile and flexural strength, and toughness. The nearly uniform properties in both directions allow for maximum toughness in the film.

Blown Film Making Machine can be used to make one large film, two smaller ones, or tubes that can be made into bags. Also, one die can make many different widths and sizes without significant trimming. This high level of flexibility in the process leads to less scrap material and higher productivity. Blown films also require lower melting temperatures than cast extrusion. Measured at the die opening, the temperature of cast film is about 220°C., where as the temperature of blown film is about 135°C. Furthermore, the cost of the equipment is approximately 50% of a line.

Applications of Blown Film Making Machine:-

Consumer food wrap from plastic wrap  article.

Agricultural  film

Bags

Industry packaging, shrink film , stretch film

Consumer packaging, food wrap, transport packaging ( Figure  )

Laminating  film

Barrier film

Multilayer film 

Research has been done to explore the incorporation of blown film extrusion into the large-scale manufacturing of carbon nanotube and  nanowire films.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Item Code: oicoExtrusion
• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 ( Days )

Two Layer Blown Film Machine:-

Additional Information:

• Item Code: Coextrusion02
• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 DAYS

Blown Film Extrusion Machine

Blown Film Extrusion Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Extrusion Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Blown Film Extrusion Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Applications of Blown Film Extrusion Machine:

·         Film for Shopping Bags

·         Film for Liners

·         Stretch Film

·         Shrink Film

·         Lamination Film

·         Biodegradable Film

Blown Film Extrusion Machine with the best combination of technology and performance. 

These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment. Blown Film Extrusion Machine has a great demand in global market for its wide range of packaging products that can be produced from it.

Blown Film Extrusion Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc.

It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be
produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 DAYS

Blown Film Machine

Blown Film Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Applications of Blown Film Machine:

· Film for Shopping Bags

· Film for Liners

· Stretch Film

· Shrink Film

· Lamination Film

· Biodegradable Film

Blown Film Machine with the best combination of technology and performance.

Blown Film Machine
These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment. Two layer ABA Die Film Making Machine has a great demand in global market for its wide range of packaging products that can be produced from it.

Blown Film Machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc.

It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be
produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Item Code: Coextrusion03
• Production Capacity: 55 - 125 ( kg/hr )
• Delivery Time: 90 DAYS

Blown Film Machinery Manufacturer

Blown Film Machinery Manufacturer with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machinery Manufacturer has a great demand in global market for its wide range of packaging products that can be produced from it. Blown Film Machinery Manufacturer is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this
single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Machinery Manufacturer:-

Additional Information:

• Production Capacity: 100 - 200 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Machinery In India

Blown Film Machinery In India with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machinery In India has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Technical Specification of Blown Film Machinery In India:-

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Machine Line

Blown Film Machine Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machine Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Machine Line:-

Additional Information:

• Production Capacity: 100 - 200 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Machinery

Blown Film Machinery with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machinery has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Technical Specification of Blown Film Machinery:-

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Machinery Exporter

Blown Film Machinery Exporter with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Machinery Exporter has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Machinery Exporter:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

2 Layer Blown Film Making Machine

2 Layer Blown Film Making Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

2 Layer Blown Film Making Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of 2 Layer Blown Film Making Machine:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

2 Layer Blown Film Making Plant

2 Layer Blown Film Making Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

2 Layer Blown Film Making Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of 2 Layer Blown Film Making Plant:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

2 Layer Blown Film Making Line

2 Layer Blown Film Making Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

2 Layer Blown Film Making Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of 2 Layer Blown Film Making Line:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

2 Layer Blown Film Machinery

2 Layer Blown Film Machinery with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

2 Layer Blown Film Machinery has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of 2 Layer Blown Film Machinery:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Plastic Film Blowing Plant

Plastic Film Blowing Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Plastic Film Blowing Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Plastic Film Blowing Plant is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Technical Specification of Plastic Film Blowing Plant:-

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Plastic Film Blowing Line

Plastic Film Blowing Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Plastic Film Blowing Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Technical Specification of Plastic Film Blowing Line:-

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Film Blowing Machine

Film Blowing Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Film Blowing Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Film Blowing Machine:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Film Blowing Plant

Film Blowing Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Film Blowing Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Film Blowing Plant:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Film Blowing Line

Film Blowing Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Film Blowing Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Film Blowing Line:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Extrusion Blown Film Machine

Extrusion Blown Film Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Extrusion Blown Film Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Technical Specification of Extrusion Blown Film Machine:-

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Blown Film Extrusion Plant

Blown Film Extrusion Plant with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Blown Film Extrusion Plant has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Blown Film Extrusion Plant:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

Extrusion Blown Film Line

Extrusion Blown Film Line with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

Extrusion Blown Film Line has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of Extrusion Blown Film Line:-

Additional Information:

• Production Capacity: 28 - 280 ( kg/hr )
• Delivery Time: 90 Working Days

2 Layer Blown Film Extrusion Machine

2 Layer Blown Film Extrusion Machine with the best combination of technology and performance. These low investment, power efficient, high - speed plants can give processors the competitive edge and quick return on their investment.

2 Layer Blown Film Extrusion Machine has a great demand in global market for its wide range of packaging products that can be produced from it. Two layer ABA Die blown film machine is an economical solution to create moderate barrier films for shopping bags, crop covers, carry bags used in textile sector, etc. It consumers low power and when it comes to return on investment, packaging industry can made good and fast profit. Similarly, two layer blown film line materials can also be produced from this single plant.

Ocean International

ExtrusionsMachinery

#extrusionsmachinery

#extrusions #machinery 

Technical Specification of 2 Layer Blown Film Extrusion Machine:-